| 不透水性：0.3MPa，30min不透水 | 断裂伸长率：无处理≥80%% | 材质：聚合物 |
| 形态：液体 | 形状：液体 | 货号：dlxfs-117 |
| 产地：广东广州 | 等级：A级 | 抗弯强度：强 |
| 抗压强度：≥0.6MPa | 拉伸强度：无处理≥1.8MPa | 品牌：德立兴防水 |
| 撕裂强度：无处理≥80% | 芯材：无 | 防水产品类别：防水涂料 |
| 规格：25kg | 是否跨境货源：否 |
***黑豹防水王
产品介绍
聚合物水泥及防水涂料，是以特定的高性能建筑液胶（简称HB型乳液胶）为主体，并配合一定比例的水泥而制成。本产品具有优良的粘结性、抗渗性、抗裂性、耐久性和耐酸碱性等功效、该产品***、***。施工方便，具有***的环境效益，系***环保防水材料。
产品用途
1. 广泛应用于墙、厕所厨间、水池、地下室、屋面及其它建筑物的防水、防渗漏、防潮等工程。
2. 用于加气混凝土、空心砖等多孔材料砌体的防渗漏、防潮。
主要技术
1. 粘结强度：与混凝土、水泥砂浆的粘结≥1.0MPa。
2. 断裂伸长率：无处理≥80%。拉伸强度：无处理≥1.8MPa。
3. 不透水性：0.3MPa，30min不透水。
4. 抗渗性：≥0.6MPa。
施工程序
1. 基层处理：基体表面应平整结实、无蜂窝、麻面、无尘土和油污、阴阳角做成弧形；施工前对基层缺陷部位要进行修补。
2. 涂底胶：在基体表面先刷一遍SJHB乳液胶。
3. 涂防水涂料：按HB乳胶液：水泥1：（0.6-0.8）的重量比拌和的防水涂料涂刷三遍，厚度到达防水规范要求，每遍涂料间隔时间约（1-2H、以不沾手为宜）。
4. 增强处理：防水层如需增强，可采用无纺布或无碱玻纤布做胎体进行增强。
5. 用量：1-2kg/m2
注意事项
1. 在使用前应搅拌均匀。
2. 水泥需用425#或以上的普通硅酸盐水泥或矿渣水泥；早强水泥不宜使用。
3. 本产品贮存在阴凉处，保存期24个月。
***黑豹防水王
Gold panther waterproof king
Product introduction产品介绍
Polymer cement and waterproof coating are made of specific high-performance building liquid glue (referred to as HB emulsion glue) with a certain proportion of cement.This product has excellent adhesion, impermeability, crack resistance, durability and acid and alkaline resistance, the product is non-toxic, pollution-free.Construction is convenient, with significant environmental benefits, is a new generation of environmental protection waterproof materials.
Product use产品用途
1. It is widely used in wall, toilet, kitchen, sink, basement, roof and other buildings to prevent water, leakage, moisture and other projects.
2. For aerated concrete, hollow brick and other porous materials masonry leakage, moisture.
The main technical主要技术
1. Bond strength: bond with concrete and cement mortar ≥ 1.0mpa.
2. Elongation at break: ≥80% without treatment.Tensile strength: ≥ 1.8mpa without treatment.
3. Water tightness: 0.3mpa, 30min.
4. Impermeability: ≥ 0.6mpa.
Construction procedures施工程序
1. Basic treatment: the surface of the matrix should be smooth and firm, without honeycomb, pitted surface, dust and oil, and the Angle of Yin and Yang should be made into arc;Repair the defective parts of the base before construction.
2. Primer adhesive: first brush SJHB emulsion adhesive on the surface of the substrate.
3. Apply waterproof coating: according to the weight ratio of HB latex liquid: cement 1: (0.6-0.8), apply the waterproof coating three times, the thickness reaches the requirements of the waterproof specification, the interval time of each coating is about (1-2h, it is advisable not to touch).
4. Enhancement treatment: if the waterproof layer needs to be enhanced, non-woven or alkali free glass fiber cloth can be used as the matrix for enhancement.
5. Dosage: 1-2kg/m2
Matters needing attention注意事项
1. Stir well before use.
2. The cement shall be 425# or above ordinary Portland cement or slag cement;Early strength cement is not suitable for use.
3. The product is stored in a cool place with a shelf life of 24 months.
